Public Profile · Graitec Advantage

Joined: 6/20/2016

Bevel weld missing

Fri, 01 Oct 2010 17:19:11 GMT – Bevel weld missing

Dumitru,
If the weld is created by joint properties, when you right click on weld & go to "Advance Properties" weld type id dimmed (gray) & can not be changed. Any other solution?

Best regards,
Greg Daneshvar
Piece marks are not in order in BOM

Fri, 01 Oct 2010 16:28:10 GMT – Piece marks are not in order in BOM

Dumitru,

Here is attached file. Thanks for reply & help.

Regards,
Greg Daneshvar
Fema 350 & Graitec

Fri, 01 Oct 2010 01:36:43 GMT – Fema 350 & Graitec

When Graitec will adopt FEMA 350 moment connectionrequirements?
I would like to see the following improvements:
1-Top & bottom flanges to be cut for RBS (reduce Beam Section) values .
2-New value from face of column to face of beam web.
3-Beam web to receive miter cut for C.J.P. weld.
4-Shear tab is no longer rectangular. it is tapered. 1" horizontal,1" vertical
5-Continuity plates need gap from inner side of column flanges & be beveledalong column flange.
6-Additional fillet weld added to top flange C.J.P.

See City of Los Angeles Building Department standard details & refer toFEMA 350 publication.

Regards,
Greg Daneshvar
All Thread on base plate & end plates.

Fri, 01 Oct 2010 00:56:51 GMT – All Thread on base plate & end plates.

When detailing base plate or end plate I like to see all thread option to use. On end plate to have an option to weld it to end plate too.

Regards,
Greg Daneshvar
Level symbol on beam shop drawings.

Fri, 01 Oct 2010 00:03:59 GMT – Level symbol on beam shop drawings.

Where & how we can set parameters to automatically insert level symbol on ALL beam shop drawings & on columns where beam is framed to that particular column. I'm attaching a sample drawings which were done by other 3D program to show the top of beam relation to column as an example.

Regards,
Greg
Bevel weld missing

Thu, 30 Sep 2010 23:56:12 GMT – Bevel weld missing

Bevel weld is missing on Moment connection, Shear plate dialog boxes. How we can have this weld option on all connection variables?
I needed to weld column stiffener to flange using C.J.P. option.
Piece marks are not in order in BOM

Thu, 30 Sep 2010 23:51:21 GMT – Piece marks are not in order in BOM

When moving a member from a sheet to other using either Drawing Management Tool or AutoCAD cut/paste option upon updating list "BOM" I notice the member piece marks are not in alphabetical order. Pleas see attache drawing & look at 29A member which is at the very bottom of list where it supposed to be at top.

Regards,
Greg
WT connection

Thu, 22 Jul 2010 16:13:04 GMT – WT connection

I have not heard any reply from Graitec so far. Hope they are working on it.

Regards,

Greg Daneshvar
WT connection

Tue, 06 Jul 2010 17:42:37 GMT – WT connection

As Daniel Miller point it out I like to use WT shape instead of shear tab. Another words we should have an additional icon for WT connection in Joint tool bar. Later on today I will send a snap shot of this connection which I applied manually to Dumitru Berteanu.
I wish we would have "File Attachment" option so everyone could view the drawings attached.

Regards,
Greg Daneshvar
WT connection

Thu, 10 Jun 2010 21:13:45 GMT – WT connection

It is common these days to use a piece of WT for beam to column connection but I don't see this option in Advance steel. Is there a way to apply without deleting intelligent connection & adding manually?
This type of connection should be used to beam ends too.

Thanks for reply.

Regards,
Greg Daneshvar

Greg Daneshvar GD Drafting Steel Detailer